Advertising
- Msa 2040 Configuration
- Hp Msa 2040 San Storage User Manual Software
- Hp Msa 2040 San Storage User Manual 2017
- Hpe Msa 2040 Manual
- HP MSA 2040 SAN Dual Controller SFF Storage/S-Buy. HP MSA System Racking Or point us to the URL where the manual is located. This document contains cable configuration information for HP MSA 2040 controller User Always operate the array in accordance with the user manual. HP MSA 2040 HP MSA 2040 SAN Controller GL100R002.
- 4 Technical white paper HP MSA 2040 Storage Configuration and Best Practices for VMware vSphere Figure 1. The HP MSA 2040 Storage array All HP MSA Storage models offer a common set of features listed in Table 1.
- Page 1: User Guide For firmware release GL200 or later Abstract This document describes initial hardware setup for HP MSA 2040 controller enclosures, and is intended for use by storage system administrators familiar with servers and computer networks, network administration, storage system installation and configuration, storage area network management, and relevant protocols.
- HP MSA 2040 User Guide HP Part Number: 723983-002 Published: September 2013 Edition: 2 Abstract This document describes initial hardware setup for HP MSA 2040 controller enclosures, and is intended for use by storage system administrators familiar with servers and computer networks, network administration, storage system installation.
Installing the enclosures
HP MSA 2040 User Guide Abstract This document describes initial hardware setup for HP MSA 2040 controller enclosures, and is intended for use by storage system administrators familiar with servers and computer networks, network administration, storage system installation and configuration, storage area network management, and relevant protocols.
Connecting the MSA 2040 controller to the SFF drive enclosure
The SFF D2700 25-drive enclosure, supporting 6 Gb internal disk drive and expander link speeds, can be
attached to an MSA 2040 controller enclosure using supported mini-SAS to mini-SAS cables of 0.5 m
(1.64') to 2 m (6.56') length [see
Connecting the MSA 2040 controller to the LFF drive enclosure
The LFF MSA 2040 6 Gb 3.5'12-drive enclosure, supporting 6 Gb internal disk drive and expander link
speeds, can be attached to an MSA 2040 controller enclosure using supported mini-SAS to mini-SAS
cables of 0.5 m (1.64') to 2 m (6.56') length [see
(page 21)].
Connecting the MSA 2040 controller to mixed model drive enclosures
MSA 2040 controllers support cabling of 6 Gb SAS link-rate LFF and SFF expansion modules—in mixed
model fashion—as shown in
(page 24), and further described in the HP MSA 2040 Cable
Configuration Guide; the HP MSA 2040 Quick Start Instructions;
QuickSpecs; and HP white papers (listed
below).
Cable requirements for MSA 2040 enclosures
IMPORTANT:
•
•
When installing SAS cables to expansion modules, use only supported mini-SAS x4 cables with
SFF-8088 connectors supporting your 6 Gb application.
•
Mini-SAS to mini-SAS 0.5 m (1.64') cables are used to connect cascaded enclosures in the rack.
•
See QuickSpecs for information about which cables are provided with your MSA 2040 products.
•
If additional or longer cables are required, they must be ordered separately (see relevant MSA 2040
QuickSpecs or P2000 G3 QuickSpecs for your products).
•
The maximum expansion cable length allowed in any configuration is 2 m (6.56').
•
Cables required, if not included, must be separately purchased.
•
When adding more than two drive enclosures, you may need to purchase additional 1 m or 2 m
cables, depending upon number of enclosures and cabling method used:
• Spanning 3, 4, or 5 drive enclosures requires 1 m (3.28') cables.
• Spanning 6 or 7 drive enclosures requires 2 m (6.56') cables.
• Spanning 3, 4, or 5 drive enclosures requires 1 m (3.28') cables.
• Spanning 6 or 7 drive enclosures requires 2 m (6.56') cables.
•
See Quickspecs (link provided above) regarding information about cables supported for host connection:
• Qualified Fibre Channel SFP and cable options
• Qualified 10GbE iSCSI SFP and cable options
• Qualified 1 Gb RJ-45 SFP and cable options
• Qualified HD mini-SAS cable options
• Qualified Fibre Channel SFP and cable options
• Qualified 10GbE iSCSI SFP and cable options
• Qualified 1 Gb RJ-45 SFP and cable options
• Qualified HD mini-SAS cable options
For additional information concerning cabling of MSA 2040 controllers and D2700 drive enclosures, visit:
Browse for the following reference documents:
•
HP MSA 2040 Cable Configuration Guide
•
HP Remote Snap technical white paper
•
HP MSA 2040 best practices
Advertising
Popular Brands
Popular manuals
Advertising
Connecting two storage systems to replicate volumes
39
The diagram below shows host interface connections and replication, with I/O and replication occurring
on different networks. For optimal protection, use two switches. Connect two ports from each controller
module to the first switch to facilitate I/O traffic, and connect two ports from each controller module to the
second switch to facilitate replication. Using two switches in tandem avoids the potential single point of
failure inherent to using a single switch; however, if one switch fails, either I/O or replication will fail, Eumig mark 610d projector user manual.
depending on which of the switches fails.
Figure 27 Connecting two storage systems for Remote Snap: multiple servers/switches/one location
Virtual Local Area Network (VLAN) and zoning can be employed to provide separate networks for iSCSI
and FC, respectively. Whether using a single switch or multiple switches for a particular interface, you can
create a VLAN or zone for I/O and a VLAN or zone for replication to isolate I/O traffic from replication
traffic. Since each switch would include both VLANs or zones, the configuration would function as multiple
networks.
Multiple servers/different networks/multiple switches
The diagram below shows the rear panel of two MSA 2040 SAN controller enclosures with both I/O and
replication occurring on different networks.
Figure 28 Connecting two storage systems for Remote Snap: multiple servers/switches/two locations
The diagram below also shows the rear-panel of two MSA 2040 SAN controller enclosures with both I/O
and replication occurring on different networks. This diagram represents two branch offices cabled to
enable disaster recovery and backup. In case of failure at either the local site or the remote site, you can
fail over the application to the available site.
6Gb/s
S
S
A
6Gb/s
S
S
A
6Gb/s
S
S
A
6Gb/s
S
S
A
Msa 2040 Configuration
MSA 2040 SAN Storage system
MSA 2040 SAN Storage system
To host server(s)
I/O switch
Switch
(replication)
6Gb/s
S
S
A
6Gb/s
S
S
A
6Gb/s
S
S
A
6Gb/s
S
S
A
Remote site 'A'
Ethernet
WAN
I/O switch
To host servers
Remote site 'B'
Hp Msa 2040 San Storage User Manual Software
To host servers
I/O switch
Peer sites with failover
MSA 2040 SAN Storage system
Hp Msa 2040 San Storage User Manual 2017
MSA 2040 SAN Storage system
Advertising
Popular Brands
Hpe Msa 2040 Manual
Popular manuals